12/8/2023 0 Comments 2014 honda odyssey tpms reset![]() Select TPMS Calibration, then press theĬustomization screen where you can choose Select Customized Settings, then press the SOURCE button.ģ. Use the i-MID and steering wheel controls, press MENU and go to Vehicle Menu.Ģ. Calibration will complete after 20 minutes of cumulative driving at 30-60 mph.ġ. If you see Calibration Failed to Start, repeat steps 2 and 3. If successful, you will see Calibration Started. Select Calibrate, then press the SEL/RESET button. To setup where you can select either cancel or calibrate.ģ. Using the display and steering wheel controls, select Vehicle Settings, then press the SEL/RE SET button. Calibration will complete after 20 minutes of cumulative driving at 30-60 mph.Ĭalibration for 2013-’15 Accord Touring, Hybrid, Plug-Inġ. If the indicator does not blink, press and hold the button again. Press and hold the TPMS button underneath the left side of the dashboard until the Low Tire Pressure/TPMS indicator blinks twice. Set the tire pressures to the recommended cold inflation values listed on the driver’s door jamb.Ĭalibration for 2013-’15 Accord (except Touring), 2014 CR-V and 2015 Fit Make sure all the tires are the same size and type.ģ. Make sure the vehicle is stopped and in neutral or park.Ģ. You can initiate the procedure, but let the customer do the driving.ġ. The procedure does not involve any tools, but is intiated by either a TPMS reset button below the steering wheel or by using a series of button presses in the i-Mid driver information center. Recalibration should be performed when the inflation is corrected or changed. The highly popular Honda Accord switched to indirect TPMS for the 2013 model year. When a tire loses air, its diameter decreases slightly. Rather, they detect a low tire by comparing relative wheel speeds via the anti-lock brake system (ABS) wheel speed sensors. Honda indirect TPMS does not have air pressure sensors inside the tires. ![]() This is not a problem with the spare tire. When a flat tire is replaced with the spare tire on a direct system vehicle, the TPMS indicator comes on (DTC 32, 34, 36 or 38) because the system is no longer receiving the signal from the flat tire’s transmitter. But, when the same code is detected more than once, the most recent one overwrites the previous one, so only the latest DTC of each type is stored. The memory can hold all the TPMS codes that could possibly be set. To clear a code, it will require a scan or TPMS tool that can communicate with the TPMS module. TPMS codes in the nonvolatile memory will not be cleared by disconnecting the battery. A healthy system will flash the light for two seconds and then turn off. Once the codes are set, the TPMS light will flash between 30-90 seconds and then remain on during the next key cycle. It does not alert the driver to low tire pressures. When a Honda TPMS detects a problem, the TPMS control unit sets a code, but shifts to fail-safe mode. The other is a TPMS warning/MIL indicator light. One light is the ISO-standard tread light that indicates that there is a low tire. ![]() Hondas typically have two TPMS lights in the instrument cluster for direct systems. The process is initiated by pressing the TPMS reset button or information center in the instrument cluster. ![]() The 28 MPH rule should also be followed after every relearn or reprogram procedure.įor indirect systems, there are three magic numbers that can be accessed by driving at 40-60 MPH for 20 minutes. The low tire pressure indicator should go off. If a customer comes in with a TPMS light on solid, inflate the tires and test-drive the vehicle at 28 MPH or more for at least one minute. Honda reasons that at this speed, there is less of a chance of interference from other sensors and radio frequencies. The speed is not detected by the sensors, it is detected through the serial data bus and the TPMS module. Once the vehicle has reached 28 MPH for at least one minute, it confirms the sensor signals, IDs and pressures. Reaching a speed of 28 MPH is the magic number for Honda direct TPMS. It is possible to key in the sensor IDs using a scan tool that can access the TPMS module. It then feeds the information through the OBDII port to the TPMS module. Most dedicated TPMS tools can activate the sensor to collect the sensor ID and its position on the vehicle. However, there are exceptions to the rule such as with the Honda Pilot (automatic relearn) and with vehicles that have indirect TPMS like the Civic, Accord and other models manufactured after 2012. There are no special tricks or procedures to avoid this process. Honda direct TPMS are different compared to domestic TPMS because they require a scan tool or a TPMS tool that connects to the OBDII port to program sensor IDs and positions.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |